芪天滴丸成型工艺的研究

邢建国1; 王新春2; 3; 薛桂蓬1; 刘宣麟1

您当前的位置：

首页 >

文章列表页 >

芪天滴丸成型工艺的研究

更新时间：2024-01-04

- 芪天滴丸成型工艺的研究
- Study on Preparation of Qitian Dropping Pills
- 中国实验方剂学杂志 2009年15卷第10期页码：47-49
- 作者机构：
- 作者简介：
- 基金信息：
  
  自治区科学研究与技术开发(含攻关)计划项目(20053312004)
- DOI：
  中图分类号：
- 纸质出版日期：2009
- 稿件说明：
移动端阅览
邢建国1, 王新春2, 3, 等. 芪天滴丸成型工艺的研究[J]. 中国实验方剂学杂志, 2009,15(10):47-49.

XING Jian-guo1, WANG Xin-chun2, 3, et al. Study on Preparation of Qitian Dropping Pills[J]. Chinese journal of experimental traditional medical formulae, 2009, 15(10): 47-49.
邢建国1, 王新春2, 3, 等. 芪天滴丸成型工艺的研究[J]. 中国实验方剂学杂志, 2009,15(10):47-49. DOI：

XING Jian-guo1, WANG Xin-chun2, 3, et al. Study on Preparation of Qitian Dropping Pills[J]. Chinese journal of experimental traditional medical formulae, 2009, 15(10): 47-49. DOI：

摘要

目的:确定芪天滴丸的最佳成型工艺。方法:以滴丸的溶散时限、外观质量和丸重差异等作为评价指标

采用单因素及正交实验设计方法对提取物与基质的用量配比

药料温度

滴速及滴距等进行优选。结果:最佳成型工艺条件为:药液温度85℃

冷却液管口温度为25℃

底部温度为5～10℃

滴速50～60滴·min-1

滴距8cm。结论:优选的成型工艺方法简便可行。

Abstract

Objective: To establish the optimized preparation of Qitian Dropping Pills.Methods: The preparation conditions

such as the proportion of the extracts and auxiliary material

the temperature of mixture

dripping speed and dripping distance etc.were studied by the orthogonal design and one-way ANOVA with three evaluation parameters including the limit of melting and dispersing time

quality of appearance and discrepancy of pill weight.Results: The optmium dripping condition was as follows: the temperature of mixture was(85 ℃

) the temperature of coolant liquid in canal orifice and at bottom was(25 ℃) and from 5 to(10 ℃

)dripping speed was 50～60 drops per minute

and dripping distance was 8 cm.Conclusion: It has been proved that the procedure is available.

关键词

Keywords

references

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

黄芩苷水溶性栓剂的制备及体外释放特性研究

通滞苏润江滴丸成型工艺

染料木素水溶性栓剂处方及制备工艺优选

复方蟾酥缓释滴丸的制备及其体外释放性能考察